WEAREONE Research Laboratory - Hydrothermal Synthesis Reactor | Polytetrafluoroethylene Inner Liner | 304 Stainless Steel high-Pressure Digestion Tank (300 ML)

💖⚙️ Match scenarios precisely | research/teaching/industry full coverage: 1. Nanomaterial synthesis - High-temperature and high-pressure hydrothermal growth of ZnO quantum dots and MOF crystals - Crystal purity > 99.9%, uniform particle size. 2. Heavy metal detection - Acid digestion of biological samples (sludge/food) - Trace lead and cadmium recovery rate ↑30%. 3. College chemistry experiments - Replace platinum crucibles for teaching, safe and low-cost - resistant to HF acid. 4. Research and development of new energy materials - Synthesis of lithium battery cathode material precursors - Reaction conversion rate increased to 98%.💖📦 Technical parameters | Type on demand: - Inner liner material: Polytetrafluoroethylene (PTFE) (temperature resistance 280℃↑) - Shell material: 304 stainless steel (anti-rust and anti-scratch) Capacity: 50ml | 100ml | 200ml (Customizable 25-2000ml is supported) - Pressure resistance limit: 3.0MPa (22MPa high-pressure model can be customized)💖⚠️ Notes The inner lining of the reaction vessel should not be filled too full, and the solution added to the total volume should be less than 80%. 2. During the tightening process of the hydrothermal reactor, place the reactor on the workbench and slowly and steadily tighten the reactor cover. Do not use a wrench to tighten the reactor cover too hard. After the reactor cover is tightened, the upper screw holes only need to be slightly tightened with a support rod. For small-sized reaction vessels, it is generally sufficient to tighten them by hand without the need for bench pliers or wrenches, which can effectively extend the service life of the inner lining. After the reaction vessel is tightened, drag the lower steel plate at the bottom of the vessel body to see if it can be dragged. If the upper steel sheet indicating the inner lining is not placed properly can be dragged (at this time, after the upper steel sheet is placed, during the process of tightening the cover, the thread gap between the cover and the reactor body generates vibration force, causing the upper steel sheet to come out), if the lower steel sheet of the reactor cannot be dragged, it indicates that the upper steel sheet has been placed properly. After heating is completed, it must be cooled naturally in the oven and not outside. Note: Do not rinse with water for cooling. Do not open it when there is pressure inside. Letting it cool to room temperature naturally can extend the service life of the reaction vessel. 5. The inner lining should not be heated alone. After the reaction is completed, it should be cleaned thoroughly and placed in a well-ventilated area to dry naturally. Do not heat the inner lining alone for drying. If the inner lining is not used for a long time, it should be placed in a stainless steel shell to avoid expansion caused by high room temperature 6. Hydrothermal reaction vessels are typically used for conducting chemical reactions under high-temperature and high-pressure conditions, and thus carry certain risks. During the heating process, risks such as pressure increase, temperature loss of control and leakage may occur. Therefore, staff members are not allowed to be present during the heating reaction process.💖⚠️ Operating instructions: Do not use in hydrofluoric acid reactions! It is recommended to use it in conjunction with an oven (≤200℃).

• ✅ MILITARY-grade safety seal: 304 stainless steel shell + PTFE inner lining, round tenon groove screw seal design, explosion-proof and leak-proof! The 1.2-meter drop resistance test showed no breakage of the bottle body and no leakage of acid solution.
• ✅ extra-wide temperature range corrosion resistance: The inner tank can withstand temperatures from -200 ° C to +280 ° C, strong acids (aqua regia/nitric acid), strong alkalis, organic solvents, and metal impurities < 10⁻¹¹g/ml.
• ✅ High pressure digestion 10 times faster: In a 3.0MPa high pressure environment, conventional insoluble samples (such as high-purity alumina, rare earth minerals) are instantly dissolved, saving 90% of the sample dissolution time.
• ✅ Lightweight laboratory gadgets: 50ml/100ml/200ml portable specifications compatible with ovens/oil baths, one-handed operation 0 threshold.
• ✅ Anti-aging: PTFE self-lubricating anti-sticking, friction coefficient remains at 0.04 after 100,000 opening and closing cycles, crystal synthesis leaves no residue, service life is 3 times that of the industry. ↑