Adhesive Dispenser Equipment,110V 800W Hot Melt Glue Spraying Gluing Machine with Pedal Switch & Pressure Gauge,302-392℉ Hot Melt Glue Spray Injecting Machine for Industries,10000CPS 6.61Lbs/h

ApplicationThis product can be widely used in manufacturing plants,workshops,construction sites,and stores for shoemaking(insole spray,sponge wrapping),toys(adhesive,fixation,insulation),box sealing,packaging,handbags,leather goods,leather bags,small household appliances,wires,hardware,small paper products,small ornaments,handicrafts,hairpins,electronic products,DIY design,and other manual or semi-automatic products that need glue.Preparation for Operation:1. Confirm the safety protection measures.2. Check if the machine is 110VAC and make sure that the pressure will not fluctuate.3. See if the temperature of the plastic bucket is set at about 302°F(different hot melt adhesives have different softening points.For specific setting values,refer to the data provided by the hot melt adhesive supplier).4. Check whether the foot switch is connected and whether any conductive objects have touched the components in the electric control box.5. Check if the air supply system is basically dry and the air pressure is stable6. Power on and test the circuit of each part.Boot Steps:1. Connect the power and turn the power switch to“ON”.2. Check if the temperature of the temperature controller is within the above range.3. Check whether the pressure relief is turned in the direction of pressure holding.4. Connect the origin,set the pressure value,and start the operation.Shutdown Steps:1.Release the foot switch to cut off the main power2.Disconnect the air pipe,or adjust the pressure regulating valve of the filter cup to 0.SpecificationColor:BlueModel:YT-X001Material:Iron and AluminumSurface Treatment:Painted,Sprayed with TeflonStyle:ModernShape:RectangularNumber of Items:1Assembly Required:YesMount Type:CountertopVoltage:110V 10APlug Model:PSB-10Max Power:1250WMax Voltage:10A 125VSol Speed:3kg/h,6.61lbs/hSolvent Capacity:3kg/h,6.61lbs/hMaximum Viscosity:10000 CPSPlug Type:US StandardPower:800WWorking Temperature:Over 150°C/302°FTemperature Control Range:150-200°C/302-392℉Pressure Range:4~10kg/8.82~22.05lbsLength of Power Cord:About 2m/6.56ftPackage Included1*Hot Melt Glue Dispenser1*Pedal Switch1*Conversion Plug1*Pressure GaugeNotes1. Please always wear safety gloves,goggles,and long-sleeved work clothes(not included)during use to avoid burning hot liquid hot melt adhesive.Before heating the melted glue,the pressure of the storage tank must be released first.After adding the sol,the lid of the glue tank must be locked.2. Please note that the gas circuit should avoid too much water vapor entering.The capacity of hot melt adhesive should not exceed one-seventh of the capacity of the storage tank.3. In order to achieve a better result and avoid damage,please set the minimum air pressure to 8.82lbs and the maximum temperature to 392℉.4. Please note that this product needs to be used with an air compressor,so you need to prepare it in advance.5. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement,and make sure you do not mind before ordering.

• PREMIUM MATERIAL:High-quality iron and aluminum make this adhesive dispenser equipment solid,wear-resistant,impact-resistant,and rustproof,so it can keep beautiful and practical without frequent replacement.The shell of the product is painted,and the aluminum barrel is sprayed with Teflon to prevent adhesion,so this item is smoother,brighter,more wear-resistant,and corrosion-resistant,thus extending its service life
• MULTIPLE FUNCTIONS:The adhesive dispenser equipment is mainly used for gluing in product processes,as well as other liquid precise points,injection,and application to the exact position of each product,and can be used for dotting,marking,circular or arcing.800W power,6.61lbs/h sol speed and solvent capacity,and 10000CPS maximum viscosity can improve your work efficiency,save labor and cost
• SAFETY GUARD:The uniform heat dissipation holes,pressure retaining design,and over-temperature protection function can timely reduce the temperature of the adhesive dispenser equipment during operation,avoid potential safety hazards,and extend the service life of it.The solid trapezoidal base can provide additional support to better maintain the stability of it.The arc design can effectively prevent your skin from being scratched compared with the traditional square corners
• ADJUSTABLE DESIGN:The temperature of adhesive dispenser equipment can be adjusted in the range of 302-392℉,and the pressure can be adjusted in the range of 8.82-22.05lbs,which are very convenient and conducive to making more beautiful and standardized items
• SIMPLE INSTALLATION AND OPERATION:The adhesive dispenser equipment with simple structure,convenient switches,practical pedal,clear pressure gauge and indication,and two models(manual and automatic)allow you to complete the installation and accurately control the amount of glue and free up your hands.This 6.56ft power cord allows you to have plenty of disposable lengths,thus reducing the limitation when you use it